top of page

Rectangular Duct Sheet-Metal Mass: Keep Thickness, Coating and Fabrication Area Separate

Oct 17
5 min read
Original warm-stone and cobalt Nexora cover showing a rectangular duct and the conversion from developed sheet area to coated-metal mass.

A ductwork takeoff reports 48 m². The supplier discusses kilograms of galvanized sheet. The fabricator adds seam material, heavier fittings and separate frames. Each figure describes a different boundary, so a single kilograms-per-square-metre shortcut can conceal several omissions. The useful estimating decision is which area, thickness and component scope a mass figure actually represents.


This article is a material-quantity illustration for rectangular sheet-metal ductwork. The selected construction thicknesses and accessories are hypothetical inputs, not recommendations. Use the approved duct construction schedule and fabricator’s developments for a real project; mass arithmetic cannot establish pressure suitability or replace construction design.


Replace an unexplained gauge with a thickness definition


Record the material, applicable specification, stated decimal thickness, thickness basis and permitted tolerance. A gauge label without its reference is insufficient evidence for a mass conversion. GalvInfoNote 1.1 explains the historical distinction between sheet-gauge systems and notes that gauge numbers represented ranges rather than one unique thickness.


For coated steel, determine whether the quoted thickness describes bare steel substrate or the total coated sheet. This distinction changes the equation. If a supplier supplies a verified mass per square metre for the actual product, use that value on the matching area basis and retain its source. Do not add a coating allowance to a product mass that already contains the coating.


SMACNA’s technical standards catalog identifies its HVAC Duct Construction Standards as guidance for metal and flexible duct fabrication and installation. The estimating schedule should follow the applicable approved construction details, including reinforcement and joints. It should never choose a thinner sheet simply because the mass calculation looks more economical.


Choose one consistent mass-per-area calculation


When bare-steel thickness is known, a useful component calculation is mA = ρsteel × tbase + c. Here mA is coated-sheet mass per plan area in kg/m², ρsteel is steel density in kg/m³, tbase is bare-metal thickness in metres, and c is coating mass in kg/m² on the same sheet-plan-area basis. If c is already the combined coating on both faces, add it once.


GalvInfoNote 1.10, Useful Galvanized Sheet Metrics, uses 7.85 kg/m² for each millimetre of steel thickness. It also explains a different calculation for total coated thickness: its theoretical sheet mass subtracts a coating factor from an equivalent all-steel sheet. Zinc and steel have different densities. That coated-thickness method and the bare-steel-plus-coating method must not be mixed.


For the example, assume bare-steel density 7,850 kg/m³ and an actual combined coating mass of 0.300 kg/m², meaning 300 g over both faces of each square metre of sheet. This 0.300 value is an invented supplier-data input. It is not obtained by treating a coating designation as an exact delivered mass. GalvInfoNote 1.1 describes Z275 as a minimum average triple-spot-test requirement of 275 g/m² total both sides, rather than an assurance that every supplied sheet contains exactly that mass.


Work from the straight duct to the developed blanks


Assume a straight duct with nominal outside metal dimensions 600 × 400 mm and length 24.0 m. Use the thin-sheet approximation for net skin area, ignoring corner-radius and neutral-axis refinements: A = 2(W + H)L = 2(0.600 + 0.400) × 24.0 = 48.0 m². This excludes end closures, fittings, seams, integral flanges and all separate hardware.


At an assumed 0.80 mm bare-steel thickness, sheet mass per area is 7,850 × 0.00080 + 0.300 = 6.58 kg/m². The corresponding net-skin mass estimate is 48.0 × 6.58 = 315.84 kg. That value is useful as a transparent subtotal, but it is not the fabricated assembly mass or the purchase quantity.


Suppose the fabricator’s checked blank schedule requires 51.0 m² for the same straight sections, including their seam and integral-flange material. The developed area is an explicit example input; it is not a universal 6.25% fabrication allowance. Those blanks contain 51.0 × 6.58 = 335.58 kg of coated sheet.


The nominal area formula is a takeoff approximation. Final blank geometry can change with corner treatment, joint arrangement and fabrication method. Where manufacturing mass accuracy matters, take the developed sheet area directly from the approved blank schedule. Do not apply the nominal perimeter formula again on top of that schedule.


Keep heavier fittings and separate hardware visible


Assume the approved fitting developments total another 8.40 m² of coated sheet at 1.00 mm bare-steel thickness. With the same hypothetical coating mass, their material weighs 7,850 × 0.00100 + 0.300 = 8.15 kg/m². Fitting-sheet mass is therefore 8.40 × 8.15 = 68.46 kg. Total developed sheet retained in the duct bodies is 335.58 + 68.46 = 404.04 kg.


A separate hardware schedule adds 38.40 kg for the example’s frames, reinforcement and fasteners. None of these components is included in the blank areas above. The defined assembly subtotal is 404.04 + 38.40 = 442.44 kg. This subtotal still excludes insulation, hangers, dampers, sealant, packaging and any equipment connected to the duct.


The distinction is important when comparing quotations. One supplier’s “duct weight” may cover bodies alone; another may include joint frames and stiffeners. Ask for the included component list before comparing a unit rate per kilogram. Likewise, do not use this simplified material subtotal directly as a lifting load or support-design load; those decisions require the complete actual assembly and the responsible engineering review.


Convert developed material into purchased input


Assume a hypothetical nesting yield of 90% for each thickness group: developed area retained in accepted duct bodies divided by sheet area issued to fabrication. For this teaching case, all remaining 10% is unrecoverable offcut loss, and there is no reusable opening or closing sheet stock. Real nesting evidence should identify reusable remnants separately.


  1. 0.80 mm group: 51.0/0.90 = 56.6667 m² of issued sheet, giving 335.58/0.90 = 372.8667 kg.

  2. 1.00 mm group: 8.40/0.90 = 9.3333 m² of issued sheet, giving 68.46/0.90 = 76.0667 kg.

  3. Total sheet input: 448.9333 kg, of which 404.04 kg remains in the defined duct bodies and 44.8933 kg is the modeled offcut loss.


Original quantity diagram showing 51.0 square metres at 6.58 kilograms per square metre plus 8.40 square metres at 8.15 equals 404.04 kilograms of duct-body sheet; adding 38.40 kilograms hardware gives 442.44 kilograms of defined assembly, while 90 percent sheet yield requires 448.93 kilograms sheet input.

Original hypothetical example. Thicknesses are bare-steel inputs; 0.300 kg/m² coating is the combined mass on both faces. Purchased sheet input and assembly mass have different boundaries.


A 90% yield means dividing by 0.90, not multiplying by 1.10. The latter would give 444.444 kg and leave this model 4.4893 kg short of the required sheet input. The separate 38.40 kg hardware is then added on its own procurement basis; it does not pass through the sheet-nesting yield.


Available sheet or coil dimensions, actual thickness tolerances, supplier rounding and minimum order quantities may change the final order. Preserve the unrounded estimate until those purchasing units are known. Also keep purchased input mass separate from material installed in the building: fabrication offcuts do not become installed duct weight.


Close the estimate with a traceable material schedule


  • Identify each thickness group and whether its thickness is bare-metal or coated-sheet thickness.

  • Retain the source for coating mass or supplier mass per square metre, with a clear one-face or two-face basis.

  • Separate nominal net surface, developed blank area, fittings, separate hardware and sheet-input yield.

  • Reconcile the final purchase schedule to stock dimensions and the fabricator’s current layout.


For a more consistent takeoff-to-pricing review, use Nexora’s paid MEP Estimators Handbook. Its published coverage includes ductwork quantity takeoff, material pricing, wastage factors and accessory allowances. Use that wider estimating framework alongside the project’s approved construction schedule and supplier data so the mass and rate columns retain the same scope.



Comments

Rated 0 out of 5 stars.
No ratings yet

Add a rating
bottom of page