Car Park Ventilation Design: ACH, Fan Sizing and CFD Checks

Illustrative image. Not a photograph of a Nexora project or a design detail.
Air changes check the quantity of air. CFD helps check where it goes.
An enclosed car park can meet its scheduled extract airflow and still have poorly swept areas behind beams, around dead-end bays or on the far side of a ramp. Start by separating three questions: how much outdoor air is required for normal operation, what resistance the fans must overcome, and whether the proposed layout actually moves air through the places that need it. Fire-mode smoke control is a separate design task, even if the equipment is shared.
Start with the design basis, not a universal ACH
Confirm which parking areas are enclosed under the applicable code, which levels interact through ramps, and which areas are served by each system. Record the code edition, adopted amendments, normal ventilation criteria, any standby mode, pollutant monitoring and the approved fire strategy. Do not apply a numerical ACH recommendation taken from another project without checking its basis.
For comparison, the International Code Council’s explanation of 2024 IMC Section 404 describes normal enclosed-parking exhaust using the served floor area. Its full-flow figure is approximately 3.8 L/(s·m²). The automatically controlled option uses carbon monoxide and nitrogen dioxide detection and has a nonzero standby minimum of approximately 0.25 L/(s·m²). These are values for that code example, not universally adopted criteria, alarm setpoints or fire-mode rates. Check local requirements before choosing sensors, their locations, control thresholds or failure responses.
Once airflow is established, air changes per hour are a useful cross-check: ACH = 3,600 × Q / V, where Q is in m³/s and the served volume V is in m³. For an area-based requirement, the same extract rate per square metre can yield a different ACH at a different ceiling height. It also tells you nothing about the airflow pattern. Nexora’s Ventilation & Exhaust Design Handbook covers airflow, replacement air, duct losses and fan selection.
Worked example: from floor area to extract duty
Take a hypothetical 3,200 m² enclosed level with a simplified average effective height of 3.0 m. For teaching the method only, assume the 2024 IMC example above is the project basis. The served volume is 9,600 m³.
Full extract: 3,200 × 3.8 = 12,160 L/s, or 12.16 m³/s.
Corresponding full-flow air change rate: 3,600 × 12.16 / 9,600 = 4.56 h⁻¹.
With the assumed automatic control option, standby: 3,200 × 0.25 = 800 L/s, or 0.80 m³/s. That corresponds to 0.30 h⁻¹ in this example. Confirm the installed equipment and control arrangement can deliver and verify the intended standby flow.
These are total rates for the assumed floor area, not instructions to size a fire-mode system. Identify the replacement-air route before selecting equipment. Check inlet louver resistance, shutter or door states, pressure differences to adjacent occupied spaces and the risk of re-entrainment near the discharge. A nominal opening area does not establish how much air will pass through it under actual pressure conditions.
Size exhaust fans against the governing duty point
Use the measured or calculated resistance of the governing path at the proposed operating flow. Include intake or extract grilles as applicable, straight runs, fittings, dampers, attenuators, louvers and discharge losses as relevant to the specific fan and pressure reference points. Keep duct static pressure, fan static pressure and fan total pressure on their respective bases. Include a component only where it belongs; a makeup-air component on a separate fan circuit is not automatically added to exhaust fan static.
As a continued example, assume one common exhaust duty of 12.16 m³/s at 325 Pa of consistently defined fan total pressure: 60 Pa at the extract terminals and connecting entries, 125 Pa in the governing run and fittings, 95 Pa across the assumed in-path equipment, and 45 Pa at the discharge assembly. The hypothetical pressure entries are not default values. At an assumed 60% overall electrical-to-air efficiency on that same total-pressure basis, electrical input is approximately 12.16 × 325 / 0.60 = 6.59 kW. This is a screening estimate, not the motor nameplate rating. Actual selection requires the manufacturer's curve, installation effects, operating air density, control range, acoustic performance and power across the allowed range.
Do not assume two parallel fans each operating at half flow will deliver the design duty unless their combined curve intersects the actual system curve there. For isolated zones, calculate each path separately. The U.S. Department of Energy fan sourcebook explains fan/system curves and installation effects. See Nexora’s fan static-pressure calculation guide for the pressure budget, and explore the HVAC Duct Pressure Loss Design Suite as a separate calculation aid. Verify its inputs and results against the project pressure budget.
Decide what CFD needs to prove
Ducted systems extract at distributed openings. Jet fans induce airflow along a path between makeup and extract points; their circulation is not additional outdoor airflow. Compare the approaches using the actual ceiling obstructions, intake/extract locations, ramp geometry and operating modes. Do not add jet-fan nominal circulation to exhaust volume when checking normal ventilation compliance.
Define the decision before opening the solver: for example, whether a proposed extract layout removes an avoidable stagnant pocket in a dead-end aisle. Document the geometry, boundary conditions, car-obstruction assumptions, source distribution and governing acceptance criteria supplied by the project. Examine airflow and pollutant results at relevant levels and locations, not only a visually attractive plane. Compare alternative operating states or uncertain inputs where they can change the decision.
Check mass balance, monitored outputs and mesh sensitivity. For a transient model, check time-step sensitivity where relevant. Numerical verification asks whether the model is solved and represented adequately; validation compares predictions with suitable measurements or benchmarks. NIST’s FDS manuals provide distinct verification and validation references for that fire-modeling tool, not project approval. Nexora’s CFD Analysis Guidance helps structure an engineering review, not certify a design.
Keep fire mode and commissioning visible
For normal operation, confirm fan speeds, flow by zone, detector response and the agreed control sequence. Check how faults are annunciated, where air enters, and whether closed doors or changed tenant layouts affect the intended air path. Make sure the commissioned arrangement can be compared with the design assumptions.
For fire mode, use the approved fire strategy, locally adopted requirements and competent specialist review. Design fire scenarios, smoke-control objectives, fan temperature rating, emergency power, equipment availability, firefighter controls and acceptance criteria must be considered on their own verified basis. A normal-operation ACH, pollutant model or attractive smoke contour is not a smoke-control acceptance result. The car park CFD design guide provides further context.
Before release: record the applicable design basis, tabulate normal and standby flow separately, verify fan and makeup-air duty at the design operating points, and connect any CFD check to a specific decision. Carry the fire-mode checks on a separate schedule so they cannot be mistaken for normal ventilation criteria.



Comments