top of page

AHU Filter Bank Sizing: Check Module Count, Actual Dimensions and Rated Flow

Oct 18
5 min read
Original teal illustration of six filter modules emphasizing module count, actual fit and model-specific airflow ratings.

An AHU drawing shows six filter modules. The schedule lists a comfortable-looking face velocity, and the replacement filters have the expected nominal size. That is not enough to close the selection. The number of usable modules, their actual dimensions and their model-specific airflow performance answer different questions. A useful filter-bank check ends with a buildable arrangement and a traceable duty for every element, rather than one velocity calculated from the cabinet outline.


1. Separate the dimensions from the performance rating


A nominal size is a purchasing designation. Actual frame dimensions establish physical fit, together with the holding frame, gasket, clamping arrangement and installation tolerance. Frontal area is the area used for a stated face-velocity calculation. Media area is the much larger unfolded filtering surface within a pleated or pocket element. These quantities must not share an unlabeled spreadsheet column.


Read the selected data sheet’s area convention. Some performance presentations use a nominal module face; others identify actual dimensions. A velocity calculated on a different area basis cannot be compared directly with that rating. Recalculating geometry does not invalidate a manufacturer’s tested airflow capacity, nor does a nominal label prove the element will seal in a particular rack.


Camfil’s Standard-Flo data sheet illustrates the information a schedule should retain: front dimensions, pocket configuration, nominal airflow and initial resistance are listed together. The same sheet identifies a maximum flow relative to nominal flow. Those conditions belong to that product family; they are not a universal allowance for other filters.


2. Start with a discrete capacity check


Consider an original hypothetical AHU with required filter-bank airflow of 5.20 m³/s, or 18,720 m³/h. The proposed bank has six identical elements in a three-column, two-row arrangement. Each element has a nominal 610 × 610 mm designation and actual outside-frame dimensions of 592 × 592 mm. Assume the project-approved selection limits each element to 0.85 m³/s at the required filtration performance and resistance criteria. This is an invented selection limit, not a rating for the Camfil products cited here.


If the six identical paths share flow equally, each receives 5.20/6 = 0.867 m³/s. Their combined permitted duty is 6 × 0.85 = 5.10 m³/s. The proposed bank is 0.10 m³/s short. Dividing the required flow by the per-element limit gives 5.20/0.85 = 6.118 elements, so the arithmetic minimum is seven complete elements. Rounding down to six defeats the check.


Seven elements may be possible in a specifically engineered housing. If the available arrangement must be a complete two-row rectangular bank, the next candidate is eight elements in four columns. Each then receives 5.20/8 = 0.650 m³/s under the equal-flow assumption, and the sum of the stated limits is 6.80 m³/s. This clears the simple per-element screen. It does not establish the final pressure drop, flow distribution or installed filtration performance.


Original comparison of six versus eight identical hypothetical filter modules at 5.20 cubic metres per second. Six need 0.867 per element against a 0.85 limit; eight need 0.650.

Original hypothetical bank check. The 0.85 m³/s per-element limit is an assumed approved selection criterion. Eight elements clear the count screen; supplier verification of resistance, distribution and physical fit is still required.


3. Reconcile the face-velocity figure without changing its meaning


For the six-element proposal, the sum of nominal square areas is 6 × 0.610² = 2.2326 m². Dividing duty by that area gives 5.20/2.2326 = 2.329 m/s. Using the actual outside-frame footprints gives 6 × 0.592² = 2.102784 m² and 5.20/2.102784 = 2.473 m/s. The actual-footprint result is 6.17% higher than the nominal-area result.


Both calculations are reproducible if labeled correctly. Neither is automatically the velocity through exposed media openings, since the frame occupies part of its own footprint. Neither should replace the selected manufacturer’s rating convention. The decisive overload in this example is still 0.867 m³/s per element against the assumed approved 0.85 m³/s limit. That conclusion does not depend on choosing whichever area produces the more favorable number.


With eight elements, the total actual footprint is 8 × 0.592² = 2.803712 m² and the corresponding average is 1.855 m/s. The physical sum of four frame widths is 2.368 m and two heights is 1.184 m. These are not finished casing dimensions: holding rails, separators, seals, clearances and construction must still be included in the supplier’s assembly drawing.


4. Keep each element’s own performance curve


Two filters can fit the same rack while having different media, pocket depth, pocket count and resistance. A shared nominal size and efficiency class do not establish identical airflow performance. Camfil’s Absolute VG Gel Seal product sheet, for example, lists dimensions, standard and maximum airflow, and resistance as separate entries. Its dimensions are explicitly actual dimensions excluding the gasket. It demonstrates why the notes and exact part number matter; it is not a recommendation to substitute that HEPA product into this illustrative AHU.


Obtain clean resistance at the proposed 0.650 m³/s per element, the project’s replacement or final-resistance criterion, and the supporting operating limits. Do not infer the eight-element pressure drop by multiplying the old six-element pressure by an area ratio. Use the actual product curve and distinguish filter resistance from losses through the holding frame, transitions and other AHU components.


For mixed-size banks, keep a row for each part number. Four elements permitted 0.85 m³/s each plus two smaller elements permitted 0.40 m³/s each total only 4.20 m³/s. Six pieces are not necessarily six equal-capacity modules. Even adding their permitted flows is only a screen: parallel paths must operate at compatible pressure drops, and unequal product resistance can produce an unequal split.


5. Verify the assembly and the replacement schedule


Check the flow arrangement rather than assuming the front elevation proves equal loading. Nearby obstructions, abrupt approach geometry and different element conditions may concentrate flow. Ask the AHU supplier to confirm the selected arrangement at the complete unit duty. A satisfactory bank average cannot establish that every element remains within its approved operating range.


Keep the procurement schedule specific enough to prevent a later substitution from undoing the selection. Record the full model, actual dimensions, seal orientation, pocket or pack configuration, quantities and approved performance data. A blanked location is not an active filter. A missing element or an unsealed perimeter is not an acceptable way of increasing the bank’s useful airflow capacity.


6. Close the review with five linked records


  • Required bank airflow, operating condition and actual or standard-air basis.

  • Element count and layout, with exact part numbers and actual fit dimensions.

  • Per-element airflow and the selected product’s rating and resistance evidence.

  • Complete housing dimensions, sealing details and replacement-access requirements.

  • Final supplier selection and an updated replacement-filter schedule after any substitution.


To review filtration alongside the rest of the unit, use the paid Air Handling Unit (AHU) Selection & Fault Diagnosis Handbook. Its publicly described filtration, submittal-review and like-for-like offer-comparison coverage supports a more consistent review. Keep the actual supplier drawings and performance data attached to the decision: a handbook cannot certify an unverified filter bank.



Comments

Rated 0 out of 5 stars.
No ratings yet

Add a rating
bottom of page