top of page

Humidity-Sensor Temperature Mismatch: Check Dew Point Before Adjusting RH

Oct 17
5 min read
Illustrative humidity transmitter and reference probe in an air duct, with a highlighted warm conduction path to the installed sensing element.

An installed humidity transmitter reports 53% RH while a reference reports 60% RH nearby. Replacing the transmitter or adding seven percentage points in software may seem reasonable. First check the temperatures at the sensing elements. A humidity element warmed above the air it is meant to represent can produce a lower RH reading even when the local water-vapor pressure is unchanged. A correctly paired temperature-and-RH comparison can separate that thermal influence from a possible calibration problem.


1. Identify which temperature belongs to the humidity reading


Relative humidity compares water-vapor pressure with saturation vapor pressure at a stated temperature. The denominator changes strongly with temperature. An accurate measurement of the humidity element's warmer local environment can therefore misrepresent the cooler duct or room that the control sequence intends to manage. This is a measurement-application error even if the element itself has not drifted.


Ask whether the displayed temperature represents the humidity element, a separate sensor elsewhere in the enclosure, or a remote air-temperature point. Also check whether the reported RH is local or already compensated to an external temperature. Do not apply a second correction to an output that the manufacturer already compensates. The signal names alone cannot establish the measurement arrangement.


Heat can reach a probe through its mounting, housing or nearby electronics. Restricted air exchange can prolong a local temperature difference. Sensirion's humidity and temperature sensor design guide, particularly its thermal and housing sections, explains why sensor-level specifications do not guarantee installed-system performance. Inspect the assembly without improvising modifications to its enclosure or electronics.


2. Calculate a temperature-only disagreement


Consider an original hypothetical example: uniform air at 24°C and 60.0% RH, with total pressure approximately 101.3 kPa. The installed sensing element is steadily warmed to 26°C. Assume unchanged local vapor pressure, no moisture source or sink, no condensation and ideal instruments at their respective sensing temperatures. The example isolates thermal mismatch; it does not predict the heat rise of a particular transmitter.


Use RH = 100 × e/es(T), where e is water-vapor partial pressure and es(T) is saturation vapor pressure at temperature T. For this room-temperature illustration, the National Physical Laboratory's conversion guidance gives the Magnus relation. In kPa, es(T) = 0.6112 × exp[17.62T/(243.12 + T)], with T in °C. This simplified calculation neglects the moist-air enhancement factor and is not a calibration reference.


  1. At 24°C, es ≈ 2.977 kPa. The air's vapor pressure is e = 0.600 × 2.977 ≈ 1.786 kPa.

  2. At the warmed 26°C element, es ≈ 3.353 kPa. The corresponding RH is 100 × 1.786/3.353 ≈ 53.3%.

  3. The difference from the representative air condition is about 6.7 percentage points. No moisture removal was assumed.

  4. A cooler 22°C element exposed to the same vapor pressure would indicate about 67.7% RH, provided it remains dry and equilibrated.


The direction matters: warming reduces RH, while cooling increases it at unchanged vapor pressure. The magnitude depends on both temperature and RH, so a fixed percentage-point offset is not a general thermal correction. Vaisala's HM70 guidance likewise warns that small probe-to-environment temperature differences can produce substantial RH errors, particularly at high humidity.


At the same vapor pressure, sensing temperatures of 22, 24 and 26 degrees Celsius correspond to 67.7, 60.0 and 53.3 percent relative humidity, all with approximately 15.8 degrees Celsius dew point.

Original hypothetical comparison at unchanged vapor pressure and approximately atmospheric pressure. No moisture exchange or condensation is assumed. Each RH value is paired with its own sensing temperature; all three pairs give approximately 15.8°C dew point.


3. Use paired dew points to test the explanation


Dew point is the temperature at which the calculated vapor pressure reaches saturation. Inverting the same relation gives Td = 243.12z/(17.62 − z), where z = ln(e/0.6112) and e is in kPa. Using unrounded example values, both the 24°C/60.0% pair and the 26°C/53.3% pair give approximately 15.8°C dew point. Agreement is consistent with a shared moisture condition and different sensing temperatures.


Now pair the warmer element's 53.3% RH with the remote 24°C air temperature. That inconsistent pair gives about 13.9°C dew point, falsely suggesting drier air. The temperature used to reconstruct vapor pressure must describe the temperature basis of that RH output. A calculated dew point cannot repair an incorrectly paired input. These figures were independently recalculated in Python and cross-checked with NPL's more detailed saturation-pressure equation.


Matching dew points are diagnostic evidence, not proof of calibration. Both calculations may contain sensor errors, and the errors may partly cancel. Conversely, a dew-point disagreement can reflect different air samples, wetting, response lag or a genuine instrument problem. Compare the result with an appropriate independent reference and the uncertainty of the complete measurement arrangement.


4. Make a controlled field comparison


  1. Record the transmitter and reference models, calibration status, locations, output definitions and operating mode. Confirm that the reference is suitable for the expected temperature and humidity.

  2. Place the reference at the intended comparison location using safe, approved access. Avoid handling the sensing tip, breathing on it or exposing it to a different jet of air.

  3. Allow both temperature and humidity readings to stabilize under the manufacturers' procedures. Record paired readings and timestamps rather than taking one quick RH snapshot.

  4. Calculate vapor pressure or dew point from each valid pair. Compare temperatures and inspect plausible heat paths before deciding whether the RH element requires adjustment.

  5. Repeat at relevant approved operating conditions. A difference that changes with airflow or surrounding temperature warrants investigation of the installation; it does not justify an arbitrary software offset.


Set acceptance limits from the project requirement, instrument specifications and comparison uncertainty. There is no universal allowable dew-point difference for this test. Vaisala's calibration guidance emphasizes thermal stabilization and warns that handling can warm the apparatus. Follow the installed model's approved calibration method if a residual discrepancy remains after the comparison conditions are controlled.


5. Recognize when the simple model stops applying


The constant-vapor-pressure comparison assumes essentially the same air and pressure, with no moisture exchange. It cannot be transferred uncritically across a cooling coil, humidifier, leaking sample line or major pressure change. A probe colder than the dew point may become wet, invalidating the dry-element calculation. Recovery and cleaning requirements depend on the instrument; follow its instructions rather than treating a saturated reading as a calibration offset.


Some instruments intentionally warm the probe. Vaisala's description of warmed-probe measurement explains how sensor temperature and RH can provide dew point, while an additional representative temperature measurement supports ambient RH calculation. Such designs should be evaluated against their specified output method. Do not disable intentional heating merely because the probe runs warmer than the air.


6. Close the issue with a repeatable measurement basis


Retain the original pairs, calculated dew points, operating conditions, uncertainty basis and approved corrective action. After any relocation, repair or adjustment, repeat the comparison and verify the control response. The closeout should explain why the measurement now represents its intended air condition. For broader psychrometric, controls and diagnostic review, use the paid Air Handling Unit (AHU) Selection & Fault Diagnosis Handbook. Its wider AHU coverage complements the installed instrument's own technical instructions.



Comments

Rated 0 out of 5 stars.
No ratings yet

Add a rating
bottom of page