top of page

Pump Minimum-Flow Recirculation: Estimate Heating in a Short Bypass Loop

Oct 18
4 min read
Original plum-and-copper pump recirculation illustration showing a short bypass loop and repeated energy input into the same water volume.

A minimum-flow bypass can circulate water through a pump while delivering little or no water to the building. That circulation may satisfy one hydraulic requirement, yet the same small volume can keep returning warmer. The important design question is where the pump’s energy leaves the active loop.


Use a heat balance to screen the proposed arrangement, then obtain manufacturer approval of the full operating envelope. The calculations below are original teaching examples. They are not a minimum-flow selection, a protective setting or a permitted running time. Local casing and seal temperatures, suction conditions and mechanical limits need separate evaluation.


1. Distinguish pump flow from heat-removing flow


Draw a boundary around the pump, bypass and every pipe or vessel that remains thermally connected in the limiting condition. If the bypass returns directly to the suction header and all load branches are closed, water may circulate without carrying energy out of that boundary. A large isolated system volume contributes no immediate thermal capacity to that small active loop.


KSB’s flow-rate definition ties minimum permissible flow to the specified speed and liquid. Minimum flow is therefore a supplier requirement, not a value established by choosing a convenient temperature-rise formula. The Hydraulic Institute’s operating-region guidance also lists temperature rise alongside hydraulic loads, vibration, power and suction considerations.


A return to a source vessel can involve more active water and a different mixing path, but the vessel is not an infinite heat sink. Verify the effective mixing volume and the mechanism for removing energy. Do not assume its complete nominal volume is immediately available if the connections allow the hot return to circulate directly back into the pump.


2. Set the energy boundary before choosing a power value


Consider a dry-motor pump whose shaft input at the recirculation duty is 4.00 kW. Assume Q = 6.00 m³/h, head H = 25.0 m, water density ρ = 1,000 kg/m³, specific heat cp = 4.18 kJ/(kg·K), and g = 9.81 m/s². These are invented operating inputs. Shaft input is taken at the actual duty, not from the motor nameplate rating.


Hydraulic output is Ph = ρgQH/1,000 with Q in m³/s. Thus Ph = 1,000 × 9.81 × (6/3,600) × 25/1,000 = 0.40875 kW. The difference between shaft input and hydraulic output is 4.00 − 0.40875 = 3.59125 kW.


KSB defines pump input power at the shaft or coupling. For this simplified example, assume the full shaft input ultimately enters the loop water, with negligible loss to room air and negligible thermal storage in metal. The external dry motor’s own losses are outside that boundary. A wet-motor assembly needs a different allocation based on its actual construction.


The 0.40875 kW of hydraulic output does not disappear: pressure energy is dissipated through the bypass and loop resistance. Pump losses plus downstream hydraulic dissipation equal the original 4.00 kW in this idealized closed path. Adding 4.00 and 0.40875 would count the hydraulic portion twice; using only 3.59125 would omit its eventual conversion within the loop.


3. Calculate a circulation-pass increment


Mass flow is 1,000 × 6/3,600 = 1.6667 kg/s. With 4.00 kW deposited over one complete circuit, the approximate temperature increment associated with a circulation pass is ΔTpass = P/(ṁcp) = 4.00/(1.6667 × 4.18) = 0.574 K. This is an energy-per-pass comparison for the complete circuit, not a prediction of the temperature difference across the pump alone.


The US Department of Energy thermodynamics handbook develops the first-law energy balance and sensible-heating relation. Here it is applied to liquid water with constant properties, no phase change and no useful energy export. A real transient loop can have temperature gradients, so one measured pair of temperatures need not equal this idealized increment.


4. Calculate the bulk heating rate of the active volume


Assume only 80.0 L is active during all-bypass operation and treat it as well mixed. Its mass is 80.0 kg and its fluid thermal capacity is 80 × 4.18 = 334.4 kJ/K. The fluid-only bulk heating rate is dT/dt = Pnet/(mcp) = 4.00/334.4 = 0.01196 K/s, or 0.718 K/min.


Original pump-bypass energy diagram. A 4.00 kilowatt shaft input splits into 3.59125 kilowatts of pump losses and 0.40875 kilowatts of hydraulic output that dissipates in the return path. The 80 litre active water loop heats at 0.718 kelvin per minute under the stated assumptions.

Original idealized heat balance for 80 L of active water at 6 m³/h, 25 m head and 4 kW shaft input. No heat loss or metal storage is included. The calculated rise is not a permitted running time.


Over an illustrative 600-second calculation interval, the estimated mean rise is 4.00 × 600/334.4 = 7.18 K. This interval is chosen only to show the arithmetic; it is not an acceptable operating duration. Ignoring metal heat capacity and ambient losses makes the bulk result a screening model, while imperfect mixing can still produce local temperatures above the mean.


The circulation turnover time is 80 L ÷ 100 L/min = 0.80 min, or 48 seconds. In ten minutes the equivalent circulating volume passes around 12.5 times, and 12.5 × 0.574 ≈ 7.18 K. This reconciles the pass calculation with the time calculation: the water repeatedly receives energy, rather than starting each pass at the original temperature.


5. Test changes without confusing flow and heat rejection


At the same net 4.00 kW, increasing active volume from 80 to 320 L reduces the ten-minute mean rise to 1.79 K. It delays warming; it does not create a steady heat-rejection mechanism. If a documented heat-removal path instead removes 0.80 kW from the 80 L loop, net input is 3.20 kW and the corresponding ten-minute rise is 5.74 K.


Increasing recirculation flow at unchanged net power reduces the energy added per pass, but does not change Pnet/(mcp). In practice a changed flow also changes pump duty and absorbed power, so recalculate both rather than claiming the heating rate is independent of every hydraulic change. Where water genuinely enters and leaves the boundary, include the associated mass-flow enthalpy terms.


6. Put the missing questions in the design review


  • What minimum continuous flow and operating region does the pump supplier approve?

  • What shaft or assembly power applies at the actual bypass duty?

  • Which water volume and metal mass remain connected, and how well do they mix?

  • Where does energy leave the boundary during low-load operation?

  • How are permitted temperature, suction and equipment limits protected by the approved sequence?


The paid Chilled Water System Design Handbook connects pump selection, piping, control sequences and design-review resources in one reference. Use that system-level framework to document the bypass boundary and the supplier questions before treating a flow reading as evidence that the complete low-load arrangement is acceptable.



Comments

Rated 0 out of 5 stars.
No ratings yet

Add a rating
bottom of page