top of page

Pump Motor Selection: Check Absorbed Power Across the Allowed Flow Range

Oct 16
5 min read
Original plum and peach illustration of a centrifugal pump and three increasing shaft-power columns, emphasizing motor review across the permitted operating range.

A chilled-water pump schedule often shows one flow, one head and one motor rating. That row is useful for tendering, but it leaves an important selection question open: what happens to absorbed shaft power when the pump operates elsewhere in its permitted range? A motor sized only from the scheduled duty can have insufficient capacity at a higher-flow condition, even when the pump head has fallen.


Review the pump and drive as a matched package. Establish the allowed flow and speed envelope, obtain the relevant power curve, and compare its maximum requirement with the motor's available output under the actual installation conditions. The original example below separates those checks without assuming that every pump has the same power-curve shape.


1. Identify which power the schedule contains


Hydraulic power delivered to the fluid is Ph = ρgVH. Pump shaft input is Ps = Ph/ηp, where ηp is pump efficiency. For water density 1,000 kg/m³, head H in metres and flow V in m³/h, shaft input in kW is Ps = 1,000 × 9.81 × V × H ÷ (3,600 × 1,000 × ηp).


KSB's power-input definition places pump input at the shaft or coupling. A conventional separate motor's rated kW normally describes mechanical output available to drive that shaft. Electrical input is larger because the motor and any drive have losses. Integrated pumps may report different boundaries, so read the equipment documentation instead of interpreting an unlabeled “kW” column.


This boundary matters when a supplier offers an 11 kW motor for a pump absorbing approximately 9 kW. The difference is not automatically wasted electrical power. Nor does the 11 kW number prove sufficient capacity under every flow, speed, ambient condition or power-supply arrangement. Those are separate selection inputs.


2. Calculate three original operating points


Consider a hypothetical clean-water centrifugal pump at one fixed speed and impeller diameter. Assume density 1,000 kg/m³ and g = 9.81 m/s². For this teaching example, the supplier allows operation from 60 to 120 m³/h under the specified application conditions. The following invented points are consistent sets of flow, head and pump efficiency; they are not a manufacturer's selection.


  • At 60 m³/h: head 34 m and pump efficiency 73%.

  • At the scheduled 90 m³/h duty: head 30 m and pump efficiency 80%.

  • At 120 m³/h: head 23 m and pump efficiency 72%.


At 60 m³/h, hydraulic power is 5.559 kW and required shaft input is 5.559/0.73 = 7.615 kW. At 90 m³/h, hydraulic power is 7.3575 kW and shaft input is 7.3575/0.80 = 9.197 kW. At 120 m³/h, hydraulic power is 7.521 kW and shaft input is 7.521/0.72 = 10.446 kW.


Head falls from 30 to 23 m between the last two points, but flow increases and efficiency decreases. Shaft power therefore rises by approximately 13.6%. Selecting the motor from head alone would miss the change. The correct comparison uses flow, head and efficiency at the same operating point.


These three points demonstrate the risk; they do not prove that no larger power demand exists between them. For the remaining worked example, explicitly assume a complete supplier review confirms 10.446 kW as the maximum shaft requirement throughout this allowed fixed-speed range. On a real project, obtain that envelope rather than fitting a convenient curve through sparse catalog points.


3. Apply the specified reserve to the governing requirement


Assume this hypothetical project requires motor output capacity at least 10% above the maximum absorbed shaft power. That reserve is an example project requirement, not a universal standard. Applying it to the governing 10.446 kW gives 11.490 kW. Applying it only to the scheduled 9.197 kW would give 10.117 kW and could make an 11 kW motor appear adequate.


KSB's drive-rating guidance discusses selection against power within the permissible range and the factors affecting required reserve. Use the pump manufacturer's requirements and the applicable project specification to establish the actual allowance. Avoid stacking several unexplained percentages when one already covers the same uncertainty.


In this example, an 11 kW motor does not meet the stated 11.490 kW requirement. A candidate 15 kW motor has sufficient nominal output, subject to the remaining checks. This is a screening result, not approval to substitute a larger motor: verify frame, coupling, starting method, controls, electrical protection and compatibility with the pump assembly.


Original pump example at 60, 90 and 120 cubic metres per hour: shaft inputs are 7.615, 9.197 and 10.446 kilowatts. A stated 10 percent reserve on the assumed envelope maximum requires 11.490 kilowatts.

Invented fixed-speed data. Three points illustrate the change; the example separately assumes a full supplier review confirms the 10.446 kW envelope maximum.


4. Compare against site-rated available output


Now suppose the motor manufacturer requires a 0.90 output factor for the actual installation and operating arrangement. This factor is deliberately assumed for arithmetic; it is not a general high-temperature or altitude correction. The 11 kW candidate then provides 9.90 kW available output, while the 15 kW candidate provides 13.50 kW.


The smaller candidate falls below the 10.446 kW pump requirement even before the example reserve. The larger candidate remains above 11.490 kW. Record the factor's source, its applicable temperature and elevation conditions, cooling arrangement and frequency range. If the manufacturer's selection already includes site derating, do not apply the same correction again.


Verify the actual liquid density and viscosity against the selected power curve; a clean-water example does not establish another fluid’s duty. For a VFD package, review the maximum approved speed and available torque throughout the intended speed range. Do not extrapolate one fixed-speed motor check into permission to overspeed. The pump, motor and drive each have limits; adequate motor kW does not resolve pump mechanical limits, suction requirements or unacceptable low-flow operation.


5. Keep electrical input and motor nameplate output separate


At the scheduled point, assume motor efficiency of 91% and drive efficiency of 97%. Electrical input is then 9.196875/(0.91 × 0.97) = 10.419 kW. If those efficiencies were unchanged at the high-flow point, input would be 10.445833/(0.91 × 0.97) = 11.834 kW. Holding efficiencies constant is another explicit simplification; obtain the actual part-load data for an energy assessment.


The candidate 15 kW nameplate does not make either point a 15 kW electrical load. Likewise, an electrical meter reading of 11.834 kW should not be compared directly with a 10.446 kW shaft requirement as though both measure the same boundary. For a field reconciliation, see pump wire-to-water efficiency.


Electrical circuit sizing, protective-device selection and drive current ratings require competent electrical review using manufacturer data and applicable requirements. Do not infer MCA or MOCP from these kW figures. A calculation of mechanical shaft power cannot replace those checks. Do not raise overload settings to make a deficient selection pass or deliberately operate outside the approved pump range during testing.


6. Ask for a reviewable selection package


  • A consistent head, efficiency and absorbed-power curve for the actual impeller, speed and fluid.

  • Defined permissible flow and speed limits, including any restrictions during pump staging or temporary operating modes.

  • The maximum shaft requirement over that envelope and the documented reserve basis.

  • Motor output available at the site conditions, with any derating already included clearly identified.

  • Drive, starting, protection and commissioning requirements for the matched assembly.


If a low-resistance operating condition can move the pump toward higher flow, include it in the review rather than treating it as an unexplained future fault. A larger motor alone cannot make that hydraulic condition acceptable; confirm that the complete pump application remains permitted.


The paid Pump Head Calculator Design Suite v1.0 provides a structured head-loss schedule, power and motor-sizing estimates, and a printable report. Use it to make the calculation basis easier to review, then attach the supplier's verified operating-envelope and motor data. That combination makes the motor choice traceable beyond the single duty point printed on the schedule.



Comments

Rated 0 out of 5 stars.
No ratings yet

Add a rating
bottom of page