top of page

Supply-Air Temperature Reset: Find the Zone That Sets the Warmest Allowable Air

Oct 19
5 min read
Original teal illustration of one AHU supplying three zones, with the west zone marking the lowest allowable supply-temperature ceiling.

An office air handler is supplying 13°C air on a mild day. Several rooms are reheating while a busy meeting room still needs cooling. Raising the supply-air temperature may help, but the meeting room has a finite airflow capacity. Before programming a reset schedule, calculate how warm the delivered air can become while that room still receives enough sensible cooling.


This is a capacity screen for a comfort VAV system, followed by a commissioning workflow. It is not a complete controls sequence or an energy-savings prediction. The Trane newsletter on multizone VAV systems explains the interaction between supply-temperature reset, zone demand, fan energy and humidity. The original example below makes one of those limits explicit.


1. Use the air temperature that actually reaches the zone


For a simplified steady sensible balance, zone load Qs = ρ × cp × V × (Tz − Ts). Here Qs is in kW, air density ρ in kg/m³, specific heat cp in kJ/(kg·K), actual delivered airflow V in m³/s, zone temperature Tz in °C, and delivered supply temperature Ts in °C. Use compatible density and flow reference conditions.


Solve at the largest permitted and demonstrably available cooling airflow: Ts,max = Tz − Qs/(ρ × cp × Vmax). This is the warmest zone supply air that meets that specific sensible load in this simplified model. It is not necessarily the temperature at the AHU sensor. Downstream fan heat, duct heat gain, leakage, mixing or active reheat can change the delivered state.


Apply the calculation to net zone sensible duty after any independently supplied cooling has been accounted for. Do not insert total sensible-plus-latent duty into this equation. Do not substitute the central coil load, which may include outdoor-air treatment and other system gains. For a zone served by several air streams, retain their individual cooling contributions instead of inventing one representative airflow.


2. Calculate three simultaneous zone limits


Assume three hypothetical zones are each maintained at 24°C. Use constant ρ = 1.20 kg/m³ and cp = 1.005 kJ/(kg·K), so ρcp = 1.206 kJ/(m³·K). Assume all delivered air has the same temperature, no reheat is active in these cooling zones, and the stated maximum flows have been verified. The following duties are simultaneous current sensible loads, not separate design-day peaks.


  • Meeting room: Qs = 6.0 kW and Vmax = 0.65 m³/s. Ts,max = 24 − 6.0/(1.206 × 0.65) = 16.35°C.

  • West office: Qs = 9.0 kW and Vmax = 0.90 m³/s. Ts,max = 24 − 9.0/(1.206 × 0.90) = 15.71°C.

  • Core office: Qs = 4.0 kW and Vmax = 0.55 m³/s. Ts,max = 24 − 4.0/(1.206 × 0.55) = 17.97°C.


The smallest limit governs: 15.71°C at the zone delivery boundary. Averaging the three limits would conceal the west office’s constraint. These figures contain no allowance for measurement uncertainty or changing occupancy. The approved operating ceiling should include a justified margin and the other system limits, rather than treating 15.71°C as a commissioning setpoint to three significant figures.


3. Test a proposed reset against the airflow requirement


At 13°C delivered air, the required meeting, west and core flows are respectively 0.452, 0.678 and 0.302 m³/s. Their combined sensible-cooling requirement is approximately 1.432 m³/s. At 15°C, the same loads require approximately 0.553, 0.829 and 0.369 m³/s, totaling 1.751 m³/s. Every zone remains below its stated maximum.


A further reset to 16°C changes the west office requirement to 9.0/[1.206 × (24 − 16)] = 0.933 m³/s. That exceeds its 0.90 m³/s limit. At the allowed maximum, the delivered cooling would be 1.206 × 0.90 × 8 = 8.683 kW, leaving a 0.317 kW shortfall. The fact that the other two zones remain comfortable does not remove this deficit.


Original three-zone temperature-limit chart: meeting 16.35°C, west 15.71°C and core 17.97°C. Proposed 16°C delivery exceeds the west-zone sensible limit.

Original steady sensible example at 24°C zone temperature, ρ=1.20 kg/m³ and cp=1.005 kJ/(kg·K). Limits exclude humidity and control margin.


The increase from 1.432 to 1.751 m³/s is about 22.2% for this fixed-load example. It is not a fan-power prediction. Ventilation minima, other zones, duct resistance, fan efficiency and pressure reset can change the actual system result. Compare whole-system operation rather than claiming that warmer supply air automatically saves a particular percentage.


4. Translate the limit to the AHU sensor


Suppose the west branch gains 0.7 K between the AHU supply sensor and the zone delivery plane at the tested operating condition. Its 15.71°C zone limit corresponds to an AHU temperature no higher than approximately 15.01°C before any control margin. If the branch gain grows at lower airflow, a fixed 0.7 K correction will not describe every condition.


Measure the relevant temperature difference at representative flow rates. Check sensor locations, calibration and timestamp alignment. A terminal discharge sensor downstream of reheat cannot validate the central supply temperature while that reheat valve is open. Record whether the quantity being compared is coil leaving, unit leaving, terminal inlet or terminal discharge temperature.


The TRACE 3D Plus temperature-control documentation includes reset methods that respond to the limiting zone. Such software options do not establish that a real terminal’s maximum airflow is available. Confirm that value through design review and TAB, including branch pressure and terminal performance.


5. Keep moisture and persistent requests visible


This calculation contains no moisture balance. A higher cooling-coil leaving temperature can reduce dehumidification, even while all room sensible balances pass. Establish project-specific humidity or dew-point limits and verify the coil’s actual leaving humidity at the proposed operating conditions. Where a separate system controls moisture, confirm its performance and availability rather than assuming that latent duty disappears.


Investigate a zone that repeatedly blocks reset. Possible causes include a real high load, inadequate maximum airflow, a biased room sensor, an obstructed branch or unintended reheat. Record the cause and approved corrective action. Removing the zone from reset logic simply because it is inconvenient can leave an occupied space without adequate cooling.


6. Commission a reversible operating envelope


  • Verify airflow, zone-temperature and delivery-temperature measurements before evaluating reset.

  • Trend simultaneous zone loads or credible demand indicators, airflow setpoints and readings, damper positions, temperatures, humidity and reset status.

  • Test an approved warmer supply condition under stable operation, then allow enough time for the zones to respond.

  • Confirm that all required airflows remain achievable, humidity remains acceptable and the temperature and pressure loops do not hunt.

  • Repeat at relevant occupancy and humid low-sensible-load conditions; document startup, fallback and recovery behavior.


To coordinate the interacting pressure loop, see VAV static-pressure reset commissioning. Check pressure and temperature demand together rather than interpreting a wide-open damper in isolation.


Keep the final result as a bounded, tested operating envelope with a named limiting zone and an explained margin. For the underlying room-load, airflow and coil-duty relationships, the paid Cooling Load Design Handbook covers those calculation boundaries with worked projects. Use project measurements and the approved controls design to turn the calculation into an operating sequence.



Comments

Rated 0 out of 5 stars.
No ratings yet

Add a rating
bottom of page